FAQ Paperless Recorders
Things to know about the ethernet connection
Table of Contents
-
The following configuration is for testing a point-to-point connection.
-
The IP address must differ in the last octet.
image
Default setting of the JUMO LOGOSCREEN nt in the delivery state
Default setting of the JUMO LOGOSCREEN nt in the delivery state
m
landscape
image
Configuring the network card
Configuring the network card
m
landscape
What does “ping” mean and how is it done?
- The console is opened via Start, Run, and entering CMD.
image
Open console
Open console
m
landscape
-
The command syntax consists of: PING space IP address e.g. ==> ping 10.11.1.77
-
The service must be activated and supported by the network.
-
The firewall must allow the command; if necessary, it must be disabled during use.
-
Ping can be used to test whether the JUMO LOGOSCREEN nt is correctly connected to the network.
-
This requires knowledge of the IP or host name of the device.
-
If the host name is known, a PING can also be sent to it.
-
The command syntax consists of: PING space host name, e.g., ==> ping jumogeraet
image
Valid ping
Valid ping
xl
landscape
image
Invalid ping
Invalid ping
xl
landscape
What is the significance of the LEDs on the network card of the JUMO LOGOSCREEN nt?
image
Network card
Network card
m
landscape
Network card status LEDs and their meanings
Left LED (green):
Network speed
on ==> 100 Mbit/s;
off ==> 10 Mbit/s
Middle LED (red):
Link and activity LED
off ==> no connection;
on ==> connection available;
flashing ==> connection available and activity on the line
Right LED (green):
Operating mode
on ==> full duplex;
off ==> half duplex
Which connection cable should I use and when?
image
The standard patch cable is used to connect the JUMO LOGOSCREEN nt to a network socket in order to establish a connection to a hub, switch router, etc.
The standard patch cable is used to connect the JUMO LOGOSCREEN nt to a network socket in order to establish a connection to a hub, switch router, etc.
m
portrait
image
Patch cables can be identified by the two plug ends with untwisted wires.
Patch cables can be identified by the two plug ends with untwisted wires.
m
landscape
image
The crossover cable is used for the direct PC connection to the JUMO LOGOSCREEN nt.
The crossover cable is used for the direct PC connection to the JUMO LOGOSCREEN nt.
m
landscape
image
The distinguishing features of a crossover cable are the two plug ends with twisted wires.
The distinguishing features of a crossover cable are the two plug ends with twisted wires.
m
portrait
image
A non-crossed patch cable can be used with the aid of an adapter.
A non-crossed patch cable can be used with the aid of an adapter.
m
landscape
How do I configure the Ethernet interface of the JUMO LOGOSCREEN nt appropriately?
a) There is no DHCP server on the network.
image
Disable the DHCP function on the recorder.
Disable the DHCP function on the recorder.
m
landscape
image
The administrator assigns a fixed IP address to the device. Advantage: The IP can be “piped.”
The administrator assigns a fixed IP address to the device. Advantage: The IP can be “piped.”
m
landscape
image
It can be used directly in JUMO applications.
It can be used directly in JUMO applications.
m
landscape
b) The router functions as a DHCP server.
image
Enable the DHCP function on the recorder.
Enable the DHCP function on the recorder.
m
landscape
-
After the power is turned off and on again, the JUMO LOGOSCREEN nt automatically receives a free IP address from the assigned range.
-
Since the recorder normally operates with a fixed IP address, it can no longer be accessed. In many cases, the IP address also changes when the power is turned off and on again.
For this reason, DHCP should only be used in conjunction with DNS. The device is assigned a HOST name. The DNS server maintains the assignments of the HOST names to the IP addresses. -
The JUMO application programs can work with the HOST name.
image
Hostname is converted to IP address
Hostname is converted to IP address
xl
landscape
image
Device list with IP addresses and connection options
Device list with IP addresses and connection options
xl
landscape
How is an entry in the device list created by the user programs?
Device list / wizard
- Example configuration of a device list entry
image
Step 1
Step 1
xl
landscape
image
Step 2
Step 2
xl
landscape
image
Step 3
Step 3
xl
landscape
image
Step 4
Step 4
xl
landscape
image
Step 5
Step 5
xl
landscape
image
Step 6
Step 6
xl
landscape
image
Step 7
Step 7
xl
landscape